Electrical Remodeling in Altadena, CA
Almost every remodel touches the electrical system. Moving a wall, opening up a kitchen, adding a bathroom or converting a garage means new circuits, relocated outlets and new lighting. Once permitted work starts, parts of the existing wiring usually have to be brought up to current code. We handle the electrical side of remodels across Altadena and the foothill communities, working directly for homeowners or alongside your general contractor.
What Electrical Remodeling Involves
Kitchens
Kitchens carry the heaviest electrical requirements in a home: at least two 20-amp small-appliance circuits for countertop receptacles, dedicated circuits for the dishwasher, disposal, microwave and refrigerator where appliances need them, a 240-volt circuit for an electric range or induction cooktop, GFCI protection at the counters, and receptacles spaced so no point along the counter is too far from an outlet. Islands and peninsulas have their own rules. Lighting is planned in layers: recessed or ceiling lighting, under-cabinet task lighting and pendants. See kitchen lighting installation.
Bathrooms
A remodelled bathroom needs a dedicated 20-amp receptacle circuit, GFCI protection, damp- or wet-rated fixtures near the tub or shower, and a humidity-controlled exhaust fan. See bathroom lighting installation.
Additions, ADUs and garage conversions
New living space means new circuits, smoke and carbon monoxide alarms, heating and cooling loads and often a sub-panel. A load calculation tells us whether the existing service can carry the new space or whether a panel upgrade is needed.
Code Upgrades a Remodel Can Trigger
When circuits are extended or modified under a permit, current code requirements apply to the new and altered work. Typical upgrades include:
- AFCI protection on modified or extended branch circuits in living areas
- GFCI protection in kitchens, bathrooms, laundry areas, garages and outdoors
- Tamper-resistant receptacles in new and replaced outlets
- Interconnected smoke and CO alarms when permitted work is done. See smoke and CO detector installation.
- Title 24 lighting rules: high-efficacy lighting, and vacancy sensors in bathrooms, garages, laundry and utility rooms
Older Altadena homes add another layer. Opening walls often exposes knob-and-tube, cloth-insulated or ungrounded wiring. A remodel is the cheapest moment to replace it, while the walls are already open. See whole-home rewiring.
How We Work on a Remodel
- Walkthrough and plan. We review the design, check the existing panel and wiring, and mark up circuits, outlets and lighting.
- Load calculation. We confirm the service can carry new appliances, EV charging or heat pumps, before anything is ordered.
- Permit. For Altadena addresses we file with LA County Public Works Building & Safety. Other cities have their own departments.
- Rough-in. New boxes and cable are installed while walls and ceilings are open, then inspected before drywall.
- Finish and final. Devices, fixtures and appliance connections go in after cabinets and finishes. We then pass final inspection and label the panel.
Rebuilding After the Eaton Fire
For rebuilds, the electrical design starts from scratch. This is the time to plan an adequate service, EV-ready circuits, surge protection and backup power. Before construction you will need a temporary power pole, and if you want backup power, see standby generator installation.
Frequently Asked Questions
Do I need an electrical permit for a remodel?
Almost always, if new circuits, relocated outlets or new wiring are involved. For Altadena addresses, permits come from LA County Public Works Building & Safety. We pull the electrical permit and schedule the inspections.
Will my old wiring have to be replaced during a remodel?
Not necessarily everywhere, but new and modified circuits must meet current code, and inspectors will flag hazards in work they can see. If walls are open anyway, replacing knob-and-tube or ungrounded wiring then is far cheaper than doing it later.
When should the electrician be involved in a remodel?
At the design stage, before cabinets and fixtures are ordered. Panel capacity, circuit layout and lighting placement all affect the design, and changing them after rough-in costs time and money.
Call (626) 768-1402 or request service online. Office hours are Monday to Sunday, 10 am to 10 pm.
Pricing: Standard service call fee applies. We quote the fee on the phone before we dispatch, and credit it toward the repair if you go ahead.